Sofa Save: DIY Upholstery

We acquired this sofa a couple of years ago. It was in good condition and sat in the waiting area of a gymnastics center. And it was almost free!

I got it specifically to reupholster, as it had the simple mid-century lines I was looking for.

BEFORE

AFTER

In the meantime, we put it in the TV room. It was so saggy that it gave me back pain to sit on it for too long. Once I was finally ready to reupholster it, the first thing I did was take off the bottom and check that the structure and springs were sound.

I was surprised to find that everything was a-okay!! The cat began his intense supervision of the whole process. Good frame means that sagging comes from the cushions, which is actually a much easier fix.

Tools/supplies:

-butter knife (for staple removal)

-pliers (for staple removal)

-staple gun

-3/8" staples

-fabric scissors

-upholstery machine needle

-zipper foot

-new upholstery fabric (about $250 CAD)

-matching upholstery thread

-zipper (I reused/repurposed mine)

-new foam cushions (about $275 CAD from Eversoft)

 

I removed the dust ruffle for a much sleeker look.

Then I removed the back panel and put it aside to use as a template for the new back panel. I also reserved the two side metal tack strips for reuse later.

The back has some curves at each corner, so that portion was adhered with special tack strips. I removed them, and put them aside as well.

With the back panel off, I began using scissors to remove the piping from the arms.

I draped my new fabric over the front of the sofa. Starting at the front bottom, I began stapling the new fabric in place.

I continued by pulling the fabric through the space between the seat and the back, pulling it tight and stapling it at the back. The same applies for the seat back. The new fabric was stapled at the back and then pushed through the space and also stapled. 

I forgot to take a photos of the arms, but they are a simple two piece, that I pinned to form the arm. Once I had my shape perfect, I sewed it, then turned it right-side in and put it on the opposite arm. The bottoms are then pushed down into the crevices and stapled within.

The cat seemed to enjoy the new fabric, even without the cushion on it. The final step is to cover all of the exposed staples with the back panel. 

The original cardboard tackstrip was basically disintegrating, so instead, I used old business cards as my tack strip. See! They come in handy for something! Once the fabric with tack strip is in place, you pull it down over the back, and you've created a clean line at the top of your panel.

The metal tack strips that were reserved during the removal, are then put on each side and tapped in with a rubber mallet. Then the bottom is pulled tight and stapled underneath.

I put the reserved bottom (crumb catcher) back on the sofa bottom, screwed the legs back on, and flipped it right side up.

With the frame now fully upholstered, I turned my attention to the new cushions. We went with a new medium-firm 6" cushion. As you can see, it is much thicker than the original 4" cushions. When ordering new cushions, measure you existing cushion from seam to seam, then add an inch to it. This will give you the nice curve to your cushions. 

I created the new cushion covers by pinning the top, bottom and side pieces to one another, and I reused the zipper from each existing cushion in the new cushions.

With the old seat cushions no longer being used, I cut them down, and used them for the new back cushions, taking them from 3" to 4" back cushions. Same process as the seat cushions.

Next, I turned my attention to bolsters. I cut them out to fit some old orange ones I had, sewed them, turned them inside out and stuffed them.

A quick hidden stitch to finish those up, and I tossed them on the new sofa! 

The final step is making sure that some cat deterrent in the form of a sticky clear panel I got off of Amazon, and ensuring a new cat scratch tree is nearby. Check and check.

I shouldn't say "final" as I do still want to add tufting buttons to the back cushions, but that will have to wait for now. Stay tuned!

The cat approves.

If you want to see how this room looked before, check out this post from the gallery wall project.

Thanks for stopping by!

Shower Room Makeover: Sad to Superb - Continued

Hey, remember that time I made over the shower room?

Well, I guess I wasn't satisfied, because here we are 3 years later, and I'm doing a thing.

Ugh, okay so here's what happened.

I was going to replace the drain in the sink. That's all I was going to do. Honestly! But, as I am pulling the drain out, it broke in half right in my hands. It was so much worse than I thought it was. Obviously, I then started to wonder what condition the bottom of the fiberglass sink was in. It was in perfect condition! Well, if you consider the fiberglass rotting where the overflow channel is, as perfect condition. I set off to the Restore (Habitat for Humanity) and it came through! There was a perfectly nice vanity of the correct size, WITH a new faucet on it. Cost me $75 bucks.

I set to changing the shut off valves, one which never really shuts off anything, so that is super helpful. But that sucker was hella on there. I had the hand torch on the solder and I was wiggling with the pliers, but no joy. Turns out that particular shut off valve has another nut to remove only the shut-off knob, so I was able to just replace that. Then I replaced the drain, p-trap and wall pipe. So basically, Almost everything under the sink is new. Yay! I guess.

Next, I She-Hulked the old vanity right out of there. There were some interesting wads of painter's tape stuck in the side then covered up with caulk. Cool.

I patched the wall, sanded, then repainted, then installed the vanity. 

Once it was in, its plain whiteness was clean, but boring.

To fix this and add texture, I bought some grass cloth.

I added it to each of the cabinet inserts.

The finished product works pretty well!

Thanks for stopping by!

Coffee Table Clean Up

I got this coffee table thanks to my friend DDT, which I outlined in this post, here. 

It was already in need of a little love back then, and now after a move across the country, it was definitely time.

Obviously the first thing I did was employ slave labour.

Once we finished sanding, we cleaned it really well, ensuring all the sand was off of it. Much to my surprise, the center of the table and the sides were not the same wood species. Cool. Cool, cool, cool, cooooo, coooo....

As you know from other posts, my favourite product is tung oil. 

I always find the instructions weird, however. Leave on 5-10 minutes and then wipe off. However, if I leave it that long, it always gums up. So, instead I apply liberally, over entire surface, and by the time I get from one end to the other (2 minutes?), I start at the beginning and remove it. This always works best for me. If you use a different product and have different results, let me know.

Additional notes:

-Before I started, I sanded a small section on the bottom of the table to see what the actual wood colour was, and used tung oil on that spot. Once I saw the colour, I decided to go ahead with tung oil.

-I re-sanded after the first coat of tung oil with 320 grit sandpaper.

-I then added two more coats.

-There are 24 hours between each coat.

With only one coat, the natural beauty of the wood is obvious. The two-tone wood is a different look than before, but I like it.

After a second coat, the cat is in agreement that this is a good look.

I have more things to finish in the living room, but this is one item off the list!

The luster/sheen of tung oil is so naturally beautiful. This is why I love this product.

A quick styling of the table includes:

-a cork trivet with a plant on it

-a wood puzzle

-some books including: Vancouver Interiors (I'm originally from BC, though not Vancouver); Borough Market in London (where I worked for a couple of years); and a book on the Arts & Crafts movement in design.

Here's a final before and after.

Thanks for stopping by!